Farmhouse sinks are renowned for their high-quality and classic appeal. The other name of Farmhouse Sinks is apron-front sinks. Apron-front sinks are continuously gaining popularity.
Farmhouse sink adds a simple sense of touch and purpose to your kitchen. They are considered sophisticated sinks that add a touch of elegance to modern kitchens.
Installing a farmhouse sink may seem daunting, but with the right tools and instructions, you can transform your kitchen or farmhouse promptly and creatively.
Here are 3 various kinds of farmhouse sinks, top-mount, flush-mount, and under-mount sinks installed in various ways and constructed from assorted variable materials. According to your preference, you can choose from unstained steel, ceramic, stone, and clay.
Top-mount sinks are installed like common sinks and can be put together fair close to any tabletop. Flush-mount sinks are as same as the tabletop and the material is also the same sometimes as the tabletop.
Under-mount farm sink dimensions are custom-built and lie beneath the tabletop. In this brief step-by-step procedure, we will give you directions for the installation of a farmhouse sink, and assurance of a prosperous and appreciated DIY task.
Can You Install a Farmhouse Sink on an Existing Countertop?
Depending on your choice of a farmhouse sink, you will need to determine if you can use your existing countertop and cabinets. The advantage of top-mount sinks is that they can be installed on any existing countertop or cabinet without alterations.
For flush-mount sinks, you may need a custom-built tabletop according to your specific purchase. On the other hand, under-mount sinks demanded their special tabletop and modifications to current cabinets.
The countertop should be water-resistant and correctly sized to fit the under-mount sink dimensions. Farmhouse sinks can be heavy, sometimes weighing hundreds of pounds. Most of the time it’s not needed to be settled.
Modification may be needed sometimes for the purpose to encourage assistance to the sink higher up.
Steps to Install a Farmhouse Sink
Here is a guide to installing an under-mount farmhouse sink, which is arguably the most complex set-up.
Image Source: Canva
Step 1: Gather Tools & Materials
The first step in installing a farmhouse sink is to gather the following tools and materials:
- Glasses for safety
- Chunks of wood four two-by-four
- Usage of drill
- A marker of Sharpie
- Usage of PVC cutter
- Sandpaper use
- Use of a knife
- Farmhouse sink
- Support for sink assist
- Silicon chalk
- Wrench adaptability
- Hand tool screwdriver
- Tape for measurement
- Fine-grit sandpaper
- Plywoord for assistance if needed
- Beneath the sink gummy/sealer
- A person to support the down sink
Step 2: Measure and Prepare
A newly purchased farmhouse sink usually comes with guidelines regarding the required cabinet setup and dimensions. Firstly, there is the requirement of measuring the cabinet’s breadth and the length of the topmost cabinet doors.
You are required to supply the sink calculations to the helping person for the installation of your tabletop.
Step 3: Check for Clearance
Ensure there is enough clearance at the front to accommodate the apron of the farmhouse sink without obstruction.
Step 4: Turn Off the Water
An essential step when undertaking any plumbing work is to shut off the water supply. It’s important to note that water damage is an expensive problem to address, and nobody wants to deal with it.
Unplug any plumbery dimension to your actual sink such as the drain pipe. Make arrangements and place a vessel below the sink in case of any water remained and also take off the waste material if you have any.
Step 5: Remove Old Sink (If Applicable)
If you’re preparing to install a new sink, you’ll need to properly remove and dispose of your old one. For detachment of the active sink, follow some guidelines.
Most likely, you’ll just need to detach the clips located beneath the sink and then cut through the caulk sealer using a sharp knife along the edge where the sink meets the countertop.
Give some pressure to stick out the sink from beneath to lose the grip and make it quite simpler to get out from the crowning. From above, grasp the center of the sink and the current faucet. Using both hands, apply upward pressure to lift the sink.
Step 6: Install Support Frame (If Required)
Sometimes, the sinks that are used in a farmhouse are weighty and might need extra support. So make sure to abide by the directions to fix it carefully, if you get a recommendation to use an extra supporting frame.
Step 7: Position the Sink
Place the sink face down on a smooth surface to ensure it remains unscathed during installation. Ensure the cabinet opening aligns with the sink and that the apron faces forward, positioned centrally.
Step 8: Attach Sink Support Brackets
Most farmhouse sinks are large and weighty and might need extra support to bear them. It can easily be done with the addition of some wood pieces by placing them horizontally. The correct method should be given in the sink fixation guide.
This will guide you on the correct distance from the top to ensure the sink sides are level. Apply wood glue to the wooden pieces. Cabinet sides should be protected with screws as well.
After the addition of wood pieces horizontally, two more should be placed vertically, so that it can be secured well. Mainly it depends on the model of the sink, it can be with extra brackets that can be secured to sink sides and fixed underneath the countertop.
Step 9: Secure the Sink
You should now have a designated area prepared for the sink. Is better to have additional help at this time for slowly putting the sink down. The sink cabinet should be coated with a layer of silicone caulk.
To ensure the farmhouse sink fits evenly in the cabinet, lower it carefully. To make sure that sink is firmly in place, you need to use wrenches for tightening support brackets
Step 10: Connect Plumbing
Now with the directions from the manufacturer, fix the drainage system if possible attach a disposal for garbage. To make sure that nothing is unsealed, connect the faucet to the water supply.
Step 11: Apply Under-Sink Adhesive/Sealant
Apply sealant to the sink’s edges where it meets the countertop and use adhesive beneath the sink. So that water will stop oozing beneath and result in harm.
Step 12: Test for Leaks and Functionality
To test the functionality and leaks in the sink, connect with the water supply to make sure that the components are working properly.
Conclusion
By following the steps outlined above, you can easily install a farmhouse sink in your kitchen. With good maintenance and care, your sink will look like a masterpiece in the kitchen. It will enhance the aesthetic appeal of your space. Now, you can enjoy working in your improved kitchen space.